Where Runoff Concentrates on North Carolina Farm Fields
Find the draws and swales where water from the ground above comes together, from public lidar, and take the map to your NRCS field office or soil and water conservation district.
Rain that runs off a field does not leave it evenly. It runs downhill and gathers in the low lines of the ground: a swale across a row-crop field, a draw at the bottom of a hillside pasture, the corner where a farm road meets the fence. NRCS calls that concentrated surface flow, and it is the condition one of its conservation practice standards is written for.
The USDA Natural Resources Conservation Service (NRCS) publishes conservation practice standards. Its Grassed Waterway standard (Code 412) defines the practice as “a shaped or graded channel that is established with suitable vegetation to convey surface water at a nonerosive velocity using a broad and shallow cross section to a stable outlet,” and says it is applied “in areas where added water conveyance capacity and vegetative protection are needed to prevent erosion and improve runoff water quality resulting from concentrated surface flow.” Among its listed purposes: “Prevent gully formation.”
NRCS’s overview of the practice adds that waterways “are constructed to convey runoff from concentrated-flow areas, terraces, or diversions where erosion control is needed,” and ends: “For further information, contact your local NRCS field office.”
So the first question on the ground is a terrain question: where does the water come together? That part you can map from your desk, for any field from the mountains to the Coastal Plain.
Map it in seven steps
- Select the field. Open Property and click the field to use the county parcel as the working area, or take up to 25 parcels at once for a whole farm. To look at one field only, draw a box or polygon instead. Open it on the map · How it works
- Map the flow paths. Run Water & Drainage. Thicker, paler lines drain more land, and tapping any line shows the acres upstream of it. A field where several faint paths join into one strong one is a field where runoff concentrates; the joins and the draw below them are the places to look at first. The terrain loaded reaches beyond your boundary, so water arriving from a neighbor’s ground or the road is counted. Open it on the map · How it works
- Check where water sits. Switch to the Ponding view to see the hollows that would hold water once full, with their depth, area and volume. Real hollows drain into the soil and evaporate, so these are upper bounds. A long strip of ponding along a farm road usually means a culvert the lidar cannot see. Open it on the map · How it works
- Follow water from one spot. Open Downhill Path and click a spot, such as a barnyard, a feeding area or the top of a draw. The line shows where rain from there runs, and the panel says how far it goes before it joins a water path, becomes a watercourse or reaches a stream. Open it on the map · How it works
- See the land draining to a point. Open Catchment and click the bottom of a draw or the corner where water leaves the field. The blue area is all the land that drains there, in acres. If much of it lies outside your boundary, the water in that draw is partly someone else’s runoff, which is worth knowing before you talk to a planner. Open it on the map · How it works
- Read slope and wet ground alongside. Slope & Aspect shows how steep the ground above each draw is, and Wetness Map ranks the field from dry ground to the flats and hollows where the shape of the land concentrates water. Neither is a soil or wetland map; they are the terrain half of the picture. Open it on the map · How it works
- Look back through old photos. Aerial History steps through every year of statewide aerial photos NC OneMap holds for a spot, 1993 to 2024–2027. Swipe between them to look for old roads, filled ditches or a stream that has moved. Open it on the map · How it works
Map the flow paths on your field
Select the parcel or draw a box, and run Water & Drainage. Free to use, no account.
Open Water & Drainage →What the map can and can’t tell you
The flow paths are traced from the USGS 3DEP bare-earth lidar model: each cell passes its water to its steepest neighbor and the land upstream of every cell is added up. That is a good picture of where the surface sends water. It is not the whole picture:
- No soil, erosion or nutrients. The tools do not model what runoff carries. EPA notes that producers “can adopt soil and water conservation practices to reduce the runoff of sediment, nutrients, bacteria, pesticides, and other pollutants from their operations,” and that the effects of runoff “vary widely, depending on the type of operation, landscape conditions, soils, climate, and farm management practices.” The terrain is one of those; the rest is on the ground. For soils, NRCS’s Web Soil Survey provides soil data and information.
- No drains or culverts. Tile drains, culverts and ditches narrower than the sampling are not in the lidar. Draw the ones you know under Culverts & barriers. On flat Coastal Plain fields a fraction of an inch can decide which way water goes.
- The ground on the day it was flown. Leveling, terraces and ditches built since the lidar survey do not show. Data Here lists which surveys cover a spot and when they were flown.
- No design. Nothing here sizes or lays out a practice. The 412 standard itself says to plan, design and construct grassed waterways “to comply with all Federal, State, and local laws and regulations,” and for its current version points readers to their NRCS state office or the Field Office Technical Guide.
Who to take the map to
- Your NRCS field office. NRCS’s North Carolina state office page says that “through a network of local field offices” NRCS in North Carolina “helps private landowners protect and enhance natural resources.” Find your local USDA Service Center with the farmers.gov service center locator. The national standard and its supporting documents are on NRCS’s Grassed Waterway page.
- Your soil and water conservation district. The NC Department of Agriculture and Consumer Services’ Division of Soil and Water Conservation has a page about the division and the districts, with a link to find your local soil and water conservation district.
What to bring: the flow path map with the acres on the main draws, the catchment of each draw you are asking about, and the slope map. The property report’s data ZIP can hold the parcel boundary, a slope map, the flow paths, a wetness map, contours and an aerial photo in one download.
Go further
Every tool runs free on the map. Files for your planner’s GIS need a pass.
Related guides
- Terrain checks before buying rural land — the checks to run on acreage before an offer.
- Contour map of your North Carolina property — contours clipped to the county parcel.
Frequently asked questions
How do I find where runoff concentrates in my field?
Select the field on the map, as a county parcel or a box you draw, and run Water & Drainage. Each flow path is labeled with the acres of land draining through it, so the draws where paths join and the figure climbs are where water from the ground above comes together. Walk those spots, ideally after a storm, to see what the water actually does there.
Can this tell me where to put a grassed waterway?
It shows where concentrated flow is, which is where NRCS’s Grassed Waterway standard (Code 412) says the practice applies. Whether a waterway or another practice fits, and how it is laid out and built, is a question for your NRCS field office or soil and water conservation district: NRCS notes that its national practice standards should not be used to plan, design or install a practice, and points to the Field Office Technical Guide for the local version. The maps help that conversation; they do not replace it.
Does the map know about my tile drains, culverts and ditches?
Not unless you draw them. Water is routed over the surface of the lidar ground model, so a culvert under a farm road or a narrow ditch is invisible to it. Draw them under Culverts & barriers in Water & Drainage and run again; the result says when your lines were used.
Does it show erosion or nutrient loss?
No. It shows where the ground sends water and where water would sit. It does not model erosion, sediment, nutrients or soil. For soils, NRCS’s Web Soil Survey provides soil data and information; for what runoff carries from a particular field, ask your soil and water conservation district.
Is it free?
Running every tool on the map is free, with no account. Downloading the flow paths, catchment outlines and grids as files needs a pass.
Sources
- USDA NRCS, Conservation Practice Standard: Grassed Waterway, Code 412 (September 2020).
- USDA NRCS, Conservation Practice Overview: Grassed Waterway (Code 412) (September 2020).
- USDA NRCS, Field Office Technical Guide, North Carolina state office and Web Soil Survey.
- USDA, Find Your Local USDA Service Center (farmers.gov).
- NC Department of Agriculture and Consumer Services, Soil & Water: About the Division & Districts.
- US EPA, Nonpoint Source: Agriculture.
About the data
Ground elevations on this site come from the USGS 3D Elevation Program (3DEP) seamless bare-earth model: 3.3 ft per pixel where a full-resolution lidar survey has been flown, about 9.8 ft per pixel where the model is built from older lidar, and about 33 ft per pixel elsewhere, with elevations above NAVD 88. The data is in the public domain. North Carolina’s statewide lidar is published through NC OneMap and carried by USGS 3DEP. USGS 3DEP serves lidar-derived elevation across North Carolina: 3.3 ft per pixel where a full-resolution lidar survey exists, about 9.8 ft per pixel where the model is built from older lidar. More from the USGS 3D Elevation Program and NC OneMap’s elevation data.