Before and After in Lidar: Western North Carolina, 2017 to 2025

Where the ground dropped and where it rose between two lidar surveys of western North Carolina, as NC OneMap publishes the difference. Two places, each one link away on the map.

The North Carolina Geological Survey compared the state’s lidar from 2016 and 2017 with the 2025 lidar over 27 western counties, and NC OneMap publishes the result as one raster: the change in ground height in each cell, later minus earlier. Elevation Change reads that raster for the area you choose and adds up what was lost and gained. Hurricane Helene came between the two surveys, in late September 2024.

On the change map, red is ground that went down and blue is ground that came up, and differences under ±1 ft are left clear as survey noise. The figures below are for a box around each place, its size given with each one, computed with the same code the map runs.

Chimney Rock: the valley floor scoured away

Chimney Rock village, Rutherford County, along the Broad River · lidar from 2017 and 2025 · box about 0.55 mi across, 187 acres with change values

Here the ground went down. In a band along the river through the village the 2025 lidar reads the ground lower than in 2017: 159,574 cu yd gone from 9.6 acres, by as much as 62 ft at the deepest cell. Treat that deepest figure with caution: NC OneMap’s own 2025 elevation model and the USGS model from the 2017 survey differ by less at that spot, and steep, scoured banks are where lidar comparisons are least reliable; the broad band of loss is solid. The wooded slopes south of the river read almost clear, and the median change across the box is 0.1 ft.

Between the two surveys came Hurricane Helene. UNC Media Hub, reporting a year later, wrote that in the late September storm “the Rocky Broad River left its banks, carved a new course and tore through shops, bridges and homes in minutes.” NC OneMap’s aerial photos from spring 2025, taken after the storm, show the valley floor stripped bare where the 2020–2023 photo has buildings beside the river. Those 2025 photos are not in Aerial History, so the photos on the map here all show the valley before the storm.

Other ground on the valley floor reads higher, 56,256 cu yd over 9.1 acres; the change map says how much, not what the material is. The single highest rise, 49 ft, is one cell whose neighbors read no change: a spike of the kind the tool’s help warns about, not ground that rose.

  • Ground lowered: 159,574 cu yd over 9.6 acres, the deepest by 62 ft
  • Ground raised: 56,256 cu yd over 9.1 acres, the highest by 49 ft
  • Median change across the box: 0.1 ft

On the map, choose Compare this view, then Compare surveys.

Mills River: an earthworks site built up

Off Research Drive, Mills River, Henderson County, beside the French Broad River · lidar from 2017 and 2025 · box about 0.55 mi across, 190 acres with change values

Here the ground mostly went up: 498,811 cu yd added over 14 acres, by up to 66 ft, against 21,827 cu yd lowered elsewhere. Nearly all of the rise is in one site north of the center of the box; the fields and woods south of it read clear.

Swipe the photos and the same block stands out. In the 2016–2019 photo there is a strip of bare, graded ground along the road with woods to the north; in 2020–2023 the bare ground reaches into those woods and holds a large graded mound; and NC OneMap’s spring 2025 photos show it larger again, built up in benches. The change map says how much the ground rose; it cannot say what the material is or what the site is for.

  • Ground lowered: 21,827 cu yd over 4.1 acres, the deepest by 14 ft
  • Ground raised: 498,811 cu yd over 14 acres, the highest by 66 ft
  • Median change across the box: 0.0 ft

On the map, choose Compare this view, then Compare surveys.

Sources

Compare the surveys in the western counties

Frame an area up to 1.24 mi across, or select a parcel, and compare. Free to use, no account.

Open Elevation Change →

How to read a change map

  • Built-up ground, such as a pad, a fill or a stockpile, shows as a patch of blue; ground cut down or scoured away shows as red.
  • A landslide shows both colors, a red scar where the ground left and blue below where it came to rest.
  • A whole area one color can be real, or an offset between the two surveys. The panel says by how much.
  • Speckle under dense trees, on water and on steep faces is mostly noise, and so is a lone cell that jumps. Trust broad, consistent patches.

Take it further

The change downloads as a GeoTIFF for GIS with a pass. The photos are on the map only.

Related guides

Frequently asked questions

Can I do this for my own property?

Where NC OneMap’s elevation change data covers it, yes. NC OneMap's elevation change data covers 27 counties in western North Carolina (Alexander, Alleghany, Ashe, Avery, Buncombe, Burke, Caldwell, Cherokee, Clay, Graham, Haywood, Henderson, Jackson, Macon, Madison, McDowell, Mitchell, Polk, Rutherford, Stokes, Surry, Swain, Transylvania, Watauga, Wilkes, Yadkin and Yancey), comparing lidar from 2016 or 2017 with lidar from 2025. There is no elevation change data for the rest of the state. Open Elevation Change, frame an area up to 1.24 mi across or select a parcel, and the panel says whether the data covers it and which two surveys it compares.

How much can I trust the numbers?

Changes smaller than ±1 ft are treated as survey noise and left out. In both boxes here the median change was 0.1 ft or less, so the two surveys agree closely on ground that did not move. The volumes are good for scale and comparison: indicative only, not a survey. The North Carolina Geological Survey, which made the data, says: “this dataset is not a professional engineering or geologic product … On its own, it is not suitable for use in design, permitting, regulatory review, real-property assessment, insurance evaluation, or life-safety decision-making. Users must independently verify the information before applying it to any professional, legal, or safety-related purpose.”

Why does a building that was destroyed or built not show?

The comparison uses bare-earth lidar, which has buildings and trees removed. Buildings and trees mostly don’t show; the ground under them does.

Will I get exactly these figures?

Only for exactly these boxes. The links open the map on each spot; the area you frame or draw there will differ a little, and so will the totals.

Can I download the change?

Comparing on the map and the before-and-after photos are free. The change itself downloads as a GeoTIFF, which needs a pass. The photos are for viewing on the map only.

About the data

Ground elevations on this site come from the USGS 3D Elevation Program (3DEP) seamless bare-earth model: 3.3 ft per pixel where a full-resolution lidar survey has been flown, about 9.8 ft per pixel where the model is built from older lidar, and about 33 ft per pixel elsewhere, with elevations above NAVD 88. The data is in the public domain. North Carolina’s statewide lidar is published through NC OneMap and carried by USGS 3DEP. USGS 3DEP serves lidar-derived elevation across North Carolina: 3.3 ft per pixel where a full-resolution lidar survey exists, about 9.8 ft per pixel where the model is built from older lidar. The comparisons read NC OneMap’s elevation change raster straight from NC OneMap, not the seamless model the other tools use. More from the USGS 3D Elevation Program and NC OneMap’s elevation data.