Data · Select an area up to 1.24 mi across in the 27 western counties

See how the ground has changed in western North Carolina

Lidar change detection for western North Carolina, free on the map, from NC OneMap's elevation change data: the North Carolina Geological Survey's comparison of lidar from 2016 or 2017 with 2025, for 27 counties in western North Carolina. There is no data for the rest of the state.

Choose an area up to 1.24 mi across. The map shades loss red and gain blue, and the panel gives the volume of ground lost and gained in cubic yards, leaving out differences small enough to be survey noise.

Free to run · pay to download

See the full result on the map free, with no account. Download a GeoTIFF of the change on NC OneMap's own grid in North Carolina State Plane (EPSG:6543), naming both surveys and the source with a pass: US$29 for 24 hours, US$99 for 30 days or US$399 for 12 months, a one-off payment in US dollars that never renews. Every download on the site is included while the pass lasts.

Who uses this

  • Buyers and owners. Check whether a property has slid, been filled or been cut between the two surveys.
  • Engineers and geologists. Get a first look at landslide volumes and deposition before ordering a survey.
  • GIS analysts. Download the change as a GeoTIFF on NC OneMap’s own grid, with both surveys and the source named in the file.

When to use it

  • You want to see what a landslide, debris flow, flood or storm did to the ground in the western counties.
  • You want to know whether a site has been filled, cut or graded since the earlier lidar.
  • You want to see how far a river bank, gravel bar or road cut has built up or worn away.

Tools for your job

Elevation Change is one step in a bigger question. These are the jobs it helps with, and the tools that go with it.

For the job: Plans, CAD, GIS and 3D printing

I need the terrain as a file.

  1. 1.Download Data — Contours, a GeoTIFF elevation model, a 3D DXF or LandXML ground surface, a georeferenced aerial photo or a 3D mesh for printing.
  2. 2.Data Here — Which USGS lidar surveys cover a spot, when each was flown, and where to get its files.
  3. 3.Elevation Change (this tool) — In the 27 western counties NC OneMap covers: whether the ground has slid, been filled or been cut between the 2016–2017 and 2025 lidar, as a GeoTIFF.
  4. 4.Contour Lines — Contours previewed on the map before you export them.
  5. 5.Elevate a File — Adds ground elevation to your own GPX, KML, GeoJSON or CSV points.
  6. 6.Point Elevation — Spot elevations at the points you click or on a grid over a lot, as CSV, GeoJSON or DXF.
  7. 7.Terrain Stats — The highest, lowest and mean ground elevation of an area, and how the land is spread between them.

How to use it

  1. Open Elevation Change and frame the area on the map, draw a box, or select a parcel with the Property tool. Areas can be up to 1.24 mi across.
  2. The panel checks whether NC OneMap’s elevation change data covers the area and names the two lidar surveys it compares there. Outside the 27 counties it says there is no data.
  3. Choose Compare surveys. Red shows where the ground went down, blue where it went up, and the panel gives the volumes.
  4. Choose Before & after photos to swipe between two years of aerial photos either side of a divider on the map: the panel picks a photo from before the earlier survey and the one nearest the later survey (in these counties the newest photo offered is older than the 2025 lidar), and either can be changed. The change colors can be laid on top.

Step by step: Chimney Rock village

We look at what changed in Chimney Rock village, in Rutherford County, between the 2017 and 2025 lidar, using NC OneMap’s elevation change data for the western counties.

1.Open Elevation Change and frame the area. The panel checks that NC OneMap’s elevation change data covers it and names the two lidar surveys it compares. Choose Compare surveys.

2.Blue is ground that rose, red is ground that dropped. The panel gives the volumes lost and gained, the biggest drop and rise, and how much of the area has data.

3.Choose Before & after photos to see aerial photos either side of a divider on the map. Drag the handle, or switch the change colors on or off.

What it showed

  • Broad, consistent patches of color are change; speckle under dense vegetation and single-spot jumps are usually survey noise.
  • Outside the 27 western counties the panel says plainly that there is no elevation change data.

How it works

The North Carolina Geological Survey compared the state's lidar from 2016 or 2017 with the 2025 lidar, county by county, and NC OneMap publishes the result as one raster: the change in ground height in each cell of about 1.5 ft, later minus earlier. The site reads that raster for your area as it is, in its own grid, with nothing interpolated; a large area takes every second cell so it stays quick.

Changes smaller than ±1 ft are treated as survey noise and left out of the totals and the colors. Volumes add up the change in every remaining cell, times the ground each cell covers.

Reading the results

Red is lower in the later survey, blue is higher. The color is darkest at the change shown under the color bar; bigger changes are the same color.

Ground lost and gained are separate totals, so a landslide that moved earth downhill shows both: a red scar and a blue deposit.

If the whole area reads higher or lower, the panel says by how much. That can be real, or an offset between the two surveys.

A large jump at a single spot can be a difference in how each survey classified the ground, not a real change. Trust broad, consistent patches.

Limits and caveats

  • Only in the 27 counties NC OneMap's elevation change data covers. NC OneMap's elevation change data covers 27 counties in western North Carolina (Alexander, Alleghany, Ashe, Avery, Buncombe, Burke, Caldwell, Cherokee, Clay, Graham, Haywood, Henderson, Jackson, Macon, Madison, McDowell, Mitchell, Polk, Rutherford, Stokes, Surry, Swain, Transylvania, Watauga, Wilkes, Yadkin and Yancey), comparing lidar from 2016 or 2017 with lidar from 2025. There is no elevation change data for the rest of the state.
  • Bare-earth lidar has buildings and trees removed, so new houses or cleared forest mostly don’t show; the earthworks under them do.
  • Water surfaces, dense vegetation and steep faces are the least reliable. Treat small changes there with caution.
  • Volumes are estimates from two separate surveys, good for scale and comparison. Indicative only, not a survey. NCGS: this dataset is not a professional engineering or geologic product … On its own, it is not suitable for use in design, permitting, regulatory review, real-property assessment, insurance evaluation, or life-safety decision-making. Users must independently verify the information before applying it to any professional, legal, or safety-related purpose.
  • Comparing on the map is free. The change GeoTIFF needs a pass. It is written on NC OneMap's own grid in North Carolina State Plane (EPSG:6543), and values in the file are in meters, converted from NC OneMap's hundredths of a foot.
  • The before and after photos are on the map only; they are not part of the download.

Data and attribution

The change comes from NC OneMap's elevation change raster, published by the North Carolina Geological Survey: its comparison of the NC Department of Public Safety's lidar from 2016 or 2017 with the 2025 lidar, read by your browser straight from NC OneMap on its own North Carolina State Plane grid. Not the elevation tiles the other map tools read. NC OneMap shares its data under a free and unrestricted use policy. The before and after photos are the years of aerial photos NC OneMap holds for the area (today’s aerial basemap where fewer than two years are found), shown on the map only.

USGS 3DEP elevation data and USGS maps are U.S. Government works in the public domain: you may use the results, including commercially. A credit to the USGS 3D Elevation Program is appreciated, and every file you download carries it. County parcel boundaries are the assessor's GIS data compiled by NC OneMap, not surveys, and the county that published each parcel is named with it. The aerial basemap is from Esri and follows Esri's terms; it is not included in downloads.

Questions

Where can I use it?

Only in the 27 counties NC OneMap's elevation change data covers. NC OneMap's elevation change data covers 27 counties in western North Carolina (Alexander, Alleghany, Ashe, Avery, Buncombe, Burke, Caldwell, Cherokee, Clay, Graham, Haywood, Henderson, Jackson, Macon, Madison, McDowell, Mitchell, Polk, Rutherford, Stokes, Surry, Swain, Transylvania, Watauga, Wilkes, Yadkin and Yancey), comparing lidar from 2016 or 2017 with lidar from 2025. There is no elevation change data for the rest of the state.

How accurate are the volumes?

Two surveys of ground that has not moved never agree exactly, so the tool ignores differences under ±1 ft. Volumes are good for scale and comparison; they are indicative only, not a survey. The North Carolina Geological Survey says the data is not an engineering or geologic product and is not suitable for design, permitting or real-property assessment on its own.

Are the aerial photos in the download?

No. The before and after photos are shown on the map only. The download is the change itself, as a GeoTIFF.

Ready to try it?

Open Elevation Change on the map →

Free to use, no account. The analysis runs in your browser on public-domain USGS 3DEP data. Downloading the results needs a pass: see pricing.

Missing something you need? Suggest a feature or ask about custom work.